U-Boot 2009.08 (Dec 03 2013 - 09:47:02) CPU: Freescale i.MX6 family TO6.4 at 792 MHz Temperature: 22 C, calibration data 0x5764d669 mx6q pll1: 792MHz mx6q pll2: 528MHz mx6q pll3: 480MHz mx6q pll8: 50MHz ipg clock : 66000000Hz ipg per clock : 66000000Hz uart clock : 80000000Hz cspi clock : 60000000Hz ahb clock : 132000000Hz axi clock : 264000000Hz emi_slow clock: 29333333Hz ddr clock : 528000000Hz usdhc1 clock : 198000000Hz usdhc2 clock : 198000000Hz usdhc3 clock : 198000000Hz usdhc4 clock : 198000000Hz nfc clock : 11000000Hz Board: CM-FX6:[ WDOG ] Boot Device: SD I2C: ready DRAM: 2 GB NAND: No NAND device found!!! 0 MiB MMC: FSL_USDHC: 0,FSL_USDHC: 1,FSL_USDHC: 2 JEDEC ID: 0x20:0x71:0x15 In: serial Out: serial Err: serial Net: got MAC address from IIM: 00:00:00:00:00:00 FEC0 Hit any key to stop autoboot: 0 mmc2 is current device reading boot.scr ** Unable to read "boot.scr" from mmc 2:1 ** reading uImage-cm-fx6 3918896 bytes read Booting from mmc ... ## Booting kernel from Legacy Image at 10800000 ... Image Name: Linux-3.0.35-cm-fx6-4 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3918832 Bytes = 3.7 MB Load Address: 10008000 Entry Point: 10008000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... Linux version 3.0.35-cm-fx6-4 (root@mainnerve-3) (gcc version 4.7.3 20130328 (pr erelease) (crosstool-NG linaro-1.13.1-4.7-2013.04-20130415 - Linaro GCC 2013.04) ) #1 SMP Thu Apr 10 16:33:50 MDT 2014 CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c53c7d CPU: VIPT nonaliasing data cache, VIPT aliasing instruction cache Machine: Compulab CM-FX6 cm_fx6_v4l_setup: cm_fx6_v4l_msize: 134217728 Memory policy: ECC disabled, Data cache writealloc CPU identified as i.MX6Q, silicon rev 1.2 PERCPU: Embedded 7 pages/cpu @cce11000 s5280 r8192 d15200 u32768 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 502272 Kernel command line: console=ttymxc3,115200 root=/dev/mmcblk0p2 rw rootwait cm_f x6_v4l_msize=128M vmalloc=256M PID hash table entries: 4096 (order: 2, 16384 bytes) Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) Memory: 960MB 1024MB = 1984MB total Memory: 2006196k/2006196k available, 90956k reserved, 1474560K highmem Virtual kernel memory layout: vector : 0xffff0000 - 0xffff1000 ( 4 kB) fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) DMA : 0xf4600000 - 0xffe00000 ( 184 MB) vmalloc : 0xe2800000 - 0xf2000000 ( 248 MB) lowmem : 0xc0000000 - 0xe2000000 ( 544 MB) pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) modules : 0xbf000000 - 0xbfe00000 ( 14 MB) .init : 0xc0008000 - 0xc0043000 ( 236 kB) .text : 0xc0043000 - 0xc0714264 (6981 kB) .data : 0xc0716000 - 0xc0773b40 ( 375 kB) .bss : 0xc0773b64 - 0xc07dc31c ( 418 kB) Hierarchical RCU implementation. RCU dyntick-idle grace-period acceleration is enabled. NR_IRQS:624 MXC GPIO hardware sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 1431655ms arm_max_freq=1GHz MXC_Early serial console at MMIO 0x21f0000 (options '115200') bootconsole [ttymxc3] enabled Console: colour dummy device 80x30 Calibrating delay loop... 1581.05 BogoMIPS (lpj=7905280) pid_max: default: 32768 minimum: 301 Security Framework initialized Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available CPU1: Booted secondary processor CPU2: Booted secondary processor CPU3: Booted secondary processor Brought up 4 CPUs SMP: Total of 4 processors activated (6324.22 BogoMIPS). devtmpfs: initialized print_constraints: dummy: NET: Registered protocol family 16 print_constraints: vddpu: 725 <--> 1300 mV at 1150 mV fast normal print_constraints: vddcore: 725 <--> 1300 mV at 1150 mV fast normal print_constraints: vddsoc: 725 <--> 1300 mV at 1200 mV fast normal print_constraints: vdd2p5: 2000 <--> 2775 mV at 2400 mV fast normal print_constraints: vdd1p1: 800 <--> 1400 mV at 1100 mV fast normal print_constraints: vdd3p0: 2625 <--> 3400 mV at 3000 mV fast normal cpu regulator mode:ldo_enable hw-breakpoint: found 6 breakpoint and 1 watchpoint registers. hw-breakpoint: 1 breakpoint(s) reserved for watchpoint single-step. hw-breakpoint: maximum watchpoint size is 4 bytes. L310 cache controller enabled l2x0: 16 ways, CACHE_ID 0x410000c7, AUX_CTRL 0x02070000, Cache size: 1048576 B bio: create slab at 0 mxs-dma mxs-dma-apbh: initialized print_constraints: ads7846_vcc: 3300 mV print_constraints: vmmc: 3300 mV vgaarb: loaded SCSI subsystem initialized spi_imx imx6q-ecspi.0: probed spi_imx imx6q-ecspi.1: probed usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb Freescale USB OTG Driver loaded, $Revision: 1.55 $ imx-ipuv3 imx-ipuv3.0: IPU DMFC NORMAL mode: 1(0~1), 5B(4,5), 5F(6,7) imx-ipuv3 imx-ipuv3.1: IPU DMFC NORMAL mode: 1(0~1), 5B(4,5), 5F(6,7) Advanced Linux Sound Architecture Driver Version 1.0.24. Bluetooth: Core ver 2.16 NET: Registered protocol family 31 Bluetooth: HCI device and connection manager initialized Bluetooth: HCI socket layer initialized Bluetooth: L2CAP socket layer initialized Bluetooth: SCO socket layer initialized Switching to clocksource mxc_timer1 NET: Registered protocol family 2 IP route cache hash table entries: 32768 (order: 5, 131072 bytes) TCP established hash table entries: 131072 (order: 8, 1048576 bytes) TCP bind hash table entries: 65536 (order: 7, 524288 bytes) TCP: Hash tables configured (established 131072 bind 65536) TCP reno registered UDP hash table entries: 512 (order: 2, 16384 bytes) UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) NET: Registered protocol family 1 RPC: Registered named UNIX socket transport module. RPC: Registered udp transport module. RPC: Registered tcp transport module. RPC: Registered tcp NFSv4.1 backchannel transport module. _regulator_get: etb supply vcore not found, using dummy regulator _regulator_get: etm.0 supply vcore not found, using dummy regulator _regulator_get: etm.1 supply vcore not found, using dummy regulator _regulator_get: etm.2 supply vcore not found, using dummy regulator _regulator_get: etm.3 supply vcore not found, using dummy regulator Static Power Management for Freescale i.MX6 wait mode is enabled for i.MX6 cpaddr = e2880000 suspend_iram_base=e28f0000 PM driver module loaded IMX usb wakeup probe add wake up source irq 75 IMX usb wakeup probe i.MXC CPU frequency driver highmem bounce pool size: 64 pages JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc. msgmni has been set to 1038 alg: No test for stdrng (krng) io scheduler noop registered io scheduler deadline registered io scheduler cfq registered (default) imx-sdma imx-sdma: loaded firmware 1.1 imx-sdma imx-sdma: initialized Serial: IMX driver imx-uart.0: ttymxc0 at MMIO 0x2020000 (irq = 58) is a IMX imx-uart.3: ttymxc3 at MMIO 0x21f0000 (irq = 61) is a IMX console [ttymxc3] enabled, bootconsole disabled console [ttymxc3] enabled, bootconsole disabled imx-uart.1: ttymxc1 at MMIO 0x21e8000 (irq = 59) is a IMX imx-uart.4: ttymxc4 at MMIO 0x21f4000 (irq = 62) is a IMX brd: module loaded loop: module loaded at24 2-0050: 256 byte at24 EEPROM, writable, 16 bytes/write ahci: SSS flag set, parallel bus scan disabled ahci ahci.0: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode ahci ahci.0: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst scsi0 : ahci_platform ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02200fff] port 0x100 irq 71 m25p80 spi0.0: found m25px16, expected m25p80 m25p80 spi0.0: m25px16 (2048 Kbytes) Creating 3 MTD partitions on "spi_flash": 0x000000000000-0x0000000c0000 : "uboot" 0x0000000c0000-0x000000100000 : "uboot environment" 0x000000100000-0x000000200000 : "reserved" No NAND device found. Chip scan failed GPMI NAND driver registered. (IMX) vcan: Virtual CAN interface driver CAN device driver interface flexcan netdevice driver flexcan imx6q-flexcan.0: device registered (reg_base=e29b0000, irq=142) FEC Ethernet Driver fec_enet_mii_bus: probed ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver fsl-ehci fsl-ehci.0: Freescale On-Chip EHCI Host Controller fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number 1 fsl-ehci fsl-ehci.0: irq 75, io base 0x02184000 fsl-ehci fsl-ehci.0: USB 2.0 started, EHCI 1.00 hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected add wake up source irq 72 fsl-ehci fsl-ehci.1: Freescale On-Chip EHCI Host Controller fsl-ehci fsl-ehci.1: new USB bus registered, assigned bus number 2 fsl-ehci fsl-ehci.1: irq 72, io base 0x02184200 fsl-ehci fsl-ehci.1: USB 2.0 started, EHCI 1.00 hub 2-0:1.0: USB hub found hub 2-0:1.0: 1 port detected Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. ARC USBOTG Device Controller driver (1 August 2005) mousedev: PS/2 mouse device common for all mice =======snvs_pwrkey_probe() lp_cr 0x20 =======snvs_pwrkey_probe() lp_cr 0x20 input: snvs_power_key as /devices/virtual/input/input0 =======snvs_pwrkey_interrupt()lpstatus 0x40060008, lp_cr 0x20 set snvs as DUMP PMIC MODE i.MX6 powerkey probe i2c-core: driver [isl29023] using legacy suspend method i2c-core: driver [isl29023] using legacy resume method i2c /dev entries driver at24 3-0050: 256 byte at24 EEPROM, writable, 16 bytes/write CM-FX6: Detected SB-FX6m (Utilite) base board rtc-em3027 3-0056: rtc core: registered rtc-em3027 as rtc0 iMX6 PCIe PCIe RC mode imx_pcie_pltfm_probe entering. ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata1.00: ATA-9: SanDisk SSD U110 32GB, U221000, max UDMA/133 ata1.00: 62533296 sectors, multi 1: LBA48 NCQ (depth 31/32) ata1.00: configured for UDMA/133 scsi 0:0:0:0: Direct-Access ATA SanDisk SSD U110 U221 PQ: 0 ANSI: 5 sd 0:0:0:0: [sda] 62533296 512-byte logical blocks: (32.0 GB/29.8 GiB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sda: sda1 sda2 sd 0:0:0:0: [sda] Attached SCSI disk PCIE: imx_pcie_pltfm_probe start link up. usb 2-1: new high speed USB device number 2 using fsl-ehci hub 2-1:1.0: USB hub found hub 2-1:1.0: 4 ports detected link up failed, DB_R0:0x0049fc00, DB_R1:0x08200000! IMX PCIe port: link down! i2c i2c-0: Added multiplexed i2c bus 3 i2c i2c-0: Added multiplexed i2c bus 4 gpio-i2cmux gpio-i2cmux: 2 port mux on imx-i2c adapter lirc_dev: IR Remote Control driver registered, major 252 IR NEC protocol handler initialized IR RC5(x) protocol handler initialized IR RC6 protocol handler initialized IR JVC protocol handler initialized IR Sony protocol handler initialized IR RC5 (streamzap) protocol handler initialized IR LIRC bridge handler initialized Linux video capture interface: v2.00 imx2-wdt imx2-wdt.0: IMX2+ Watchdog Timer enabled. timeout=60s (nowayout=1) sdhci: Secure Digital Host Controller Interface driver sdhci: Copyright(c) Pierre Ossman mmc0: SDHCI controller on platform [sdhci-esdhc-imx.0] using DMA mmc1: SDHCI controller on platform [sdhci-esdhc-imx.2] using DMA VPU initialized mxc_asrc registered Thermal calibration data is 0x5764d669 Thermal sensor with ratio = 180 Anatop Thermal registered as thermal_zone0 anatop_thermal_probe: default cooling device is cpufreq! caam caam.0: device ID = 0x0a16010000000000 caam caam.0: job rings = 2, qi = 0 alg: No test for authenc(hmac(md5),cbc(aes)) (authenc-hmac-md5-cbc-aes-caam) caam caam.0: authenc-hmac-md5-cbc-aes-caam alg: No test for authenc(hmac(sha1),cbc(aes)) (authenc-hmac-sha1-cbc-aes-caam) caam caam.0: authenc-hmac-sha1-cbc-aes-caam alg: No test for authenc(hmac(sha224),cbc(aes)) (authenc-hmac-sha224-cbc-aes-caam) caam caam.0: authenc-hmac-sha224-cbc-aes-caam alg: No test for authenc(hmac(sha256),cbc(aes)) (authenc-hmac-sha256-cbc-aes-caam) mmc0: new high speed SDIO card at address 0001 caam caam.0: authenc-hmac-sha256-cbc-aes-caam alg: No test for authenc(hmac(md5),cbc(des3_ede)) (authenc-hmac-md5-cbc-des3_ede-caam) caam caam.0: authenc-hmac-md5-cbc-des3_ede-caam alg: No test for authenc(hmac(sha1),cbc(des3_ede)) (authenc-hmac-sha1-cbc-des3_ede-caam) caam caam.0: authenc-hmac-sha1-cbc-des3_ede-caam alg: No test for authenc(hmac(sha224),cbc(des3_ede)) (authenc-hmac-sha224-cbc-des3_ede-caam) caam caam.0: authenc-hmac-sha224-cbc-des3_ede-caam alg: No test for authenc(hmac(sha256),cbc(des3_ede)) (authenc-hmac-sha256-cbc-des3_ede-caam) caam caam.0: authenc-hmac-sha256-cbc-des3_ede-caam alg: No test for authenc(hmac(md5),cbc(des)) (authenc-hmac-md5-cbc-des-caam) caam caam.0: authenc-hmac-md5-cbc-des-caam alg: No test for authenc(hmac(sha1),cbc(des)) (authenc-hmac-sha1-cbc-des-caam) caam caam.0: authenc-hmac-sha1-cbc-des-caam alg: No test for authenc(hmac(sha224),cbc(des)) (authenc-hmac-sha224-cbc-des-caam) caam caam.0: authenc-hmac-sha224-cbc-des-caam alg: No test for authenc(hmac(sha256),cbc(des)) (authenc-hmac-sha256-cbc-des-caam) caam caam.0: authenc-hmac-sha256-cbc-des-caam caam caam.0: cbc-aes-caam caam caam.0: cbc-3des-caam caam caam.0: cbc-des-caam mmc1: host does not support reading read-only switch. assuming write-enable. mmc1: new high speed SDHC card at address eb42 mmcblk0: mmc1:eb42 SD08G 7.42 GiB mmcblk0: p1 p2 platform caam_jr.0: registering rng-caam usbcore: registered new interface driver usbhid usbhid: USB HID core driver usbcore: registered new interface driver snd-usb-audio mxc_spdif mxc_spdif.0: MXC SPDIF Audio _regulator_get: 2-001a supply AVDD not found, using dummy regulator _regulator_get: 2-001a supply HPVDD not found, using dummy regulator _regulator_get: 2-001a supply DCVDD not found, using dummy regulator _regulator_get: 2-001a supply DBVDD not found, using dummy regulator imx_wm8731_init: success asoc: wm8731-hifi <-> imx-ssi.1 mapping ok asoc: mxc-spdif <-> imx-spdif-dai.0 mapping ok ALSA device list: #0: wm8731-audio #1: imx-spdif NET: Registered protocol family 26 TCP cubic registered NET: Registered protocol family 17 can: controller area network core (rev 20090105 abi 8) NET: Registered protocol family 29 can: raw protocol (rev 20090105) can: broadcast manager protocol (rev 20090105 t) Bluetooth: RFCOMM TTY layer initialized Bluetooth: RFCOMM socket layer initialized Bluetooth: RFCOMM ver 1.11 Bluetooth: BNEP (Ethernet Emulation) ver 1.3 Bluetooth: BNEP filters: protocol multicast Bluetooth: HIDP (Human Interface Emulation) ver 1.2 lib80211: common routines for IEEE802.11 drivers HDMI CEC initialized mxc_vdoa mxc_vdoa: i.MX Video Data Order Adapter(VDOA) driver probed mxc_sdc_fb mxc_sdc_fb.0: register mxc display driver hdmi mxc_hdmi mxc_hdmi: Detected HDMI controller 0x13:0xa:0xa0:0xc1 imx-ipuv3 imx-ipuv3.0: IPU DMFC DP HIGH RESOLUTION: 1(0,1), 5B(2~5), 5F(6,7) Console: switching to colour frame buffer device 240x67 mxc_sdc_fb mxc_sdc_fb.1: register mxc display driver dvi _regulator_get: get() with no identifier mxc_hdmi_soc mxc_hdmi_soc.0: MXC HDMI Audio asoc: mxc-hdmi-soc <-> imx-hdmi-soc-dai.0 mapping ok mxc_v4l2_output mxc_v4l2_output.0: V4L2 device registered as video16 mxc_v4l2_output mxc_v4l2_output.0: V4L2 device registered as video17 mxc_v4l2_output mxc_v4l2_output.0: V4L2 device registered as video18 VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 Bus freq driver module loaded Bus freq driver Enabled mxc_dvfs_core_probe DVFS driver module loaded regulator_init_complete: ads7846_vcc: incomplete constraints, leaving on rtc-em3027 3-0056: setting system clock to 2014-04-15 15:11:20 UTC (1397574680) EXT3-fs (mmcblk0p2): error: couldn't mount because of unsupported optional features (240) EXT2-fs (mmcblk0p2): error: couldn't mount because of unsupported optional features (244) EXT4-fs (mmcblk0p2): recovery complete EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null) VFS: Mounted root (ext4 filesystem) on device 179:2. devtmpfs: mounted Freeing init memory: 236K INIT: version 2.88 booting INIT: /etc/inittab[70]: action field too long [info] Using makefile-style concurrent boot in runlevel S. [....] Starting the hotplug events dispatcher: udevdudevd[1467]: starting version 175 . ok [....] Synthesizing the initial hotplug events...ads7846 spi0.1: touchscreen, irq 303 input: ADS7846 Touchscreen as /devices/platform/imx6q-ecspi.0/spi_master/spi0/spi0.1/input/input1 done. [....] Waiting for /dev to be fully popuBluetooth: vendor=0x2df, device=0x911a, class=255, fn=2 lated...cfg80211: Calling CRDA to update world regulatory domain cfg80211: World regulatory domain updated: cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) mwifiex_sdio mmc0:0001:1: WLAN FW already running! Skip FW download mwifiex_sdio mmc0:0001:1: WLAN FW is active mwifiex_sdio mmc0:0001:1: driver_version = mwifiex 1.0 (14.66.9.p96) done. Starting fake hwclock: loading system time. Unable to read saved clock information: /etc/fake-hwclock.data does not exist [ ok ] Setting parameters of disc: (none). [ ok ] Activating swap...done. EXT4-fs (mmcblk0p2): re-mounted. Opts: (null) [ ok ] Cleaning up temporary files... /tmp. [ ok ] Activating lvm and md swap...done. [....] Checking file systems...fsck from util-linux 2.20.1 done. [ ok ] Mounting local filesystems...done. [ ok ] Activating swapfile swap...done. [ ok ] Cleaning up temporary files.... [ ok ] Setting kernel variables ...done. [....] Configuring network interfaces...NET: Registered protocol family 10 Internet Systems Consortium DHCP Client 4.2.2 Copyright 2004-2011 Internet Systems Consortium. All rights reserved. For info, please visit https://www.isc.org/software/dhcp/ eth0: Freescale FEC PHY driver [Generic PHY] (mii_bus:phy_addr=1:00, irq=-1) ADDRCONF(NETDEV_UP): eth0: link is not ready Listening on LPF/eth0/00:01:c0:14:9d:2a Sending on LPF/eth0/00:01:c0:14:9d:2a Sending on Socket/fallback DHCPREQUEST on eth0 to 255.255.255.255 port 67 PHY: 1:00 - Link is Up - 100/Full ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready DHCPREQUEST on eth0 to 255.255.255.255 port 67 DHCPACK from 10.21.21.1 bound to 10.21.21.78 -- renewal in 147505 seconds. done. [ ok ] Cleaning up temporary files.... [....] Setting up ALSA...amixer: Invalid command! done. [info] Setting console screen modes and fonts. setterm: cannot (un)set powersave mode: Invalid argument [ ok ] Setting up X socket directories... /tmp/.X11-unix /tmp/.ICE-unix. INIT: Entering runlevel: 2 [info] Using makefile-style concurrent boot in runlevel 2. [ ok ] Starting enhanced syslogd: rsyslogd. [ ok ] Starting periodic command scheduler: cron. [ ok ] Starting system message bus: dbus. saned disabled; edit /etc/default/saned [ ok ] Starting network connection manager: NetworkManager.